Adrian Bowyer
409af6bb11
Manual Z probing added to G30 (see http://reprap.org/wiki/G-code ).
2013-11-28 11:57:38 +00:00
Adrian Bowyer
a4d8f41271
G31 now waits for moves to end before measuring/reporting. G30 implemented. Has argument Pn n = 0,1,2 - takes probe reading at current XY and calls them point n for the purpose of bed plane calculation. Add an S field on the last probe (i.e. when n=2 usually, though you can do them in any order) to get it to fit the bed plane.
2013-11-27 22:59:37 +00:00
Adrian Bowyer
7b9894e543
M206 implemented. This commit has the ethernet enabled and heaters set on by 1 (i.e. Duet v0.5 or below).
2013-11-26 15:12:24 +00:00
Adrian Bowyer
c0b7b4bace
Working on the ether/USB problem. The network can now be disabled (#define NETWORK in Configuration.h). With it disabled the USB works with or without a network cable plugged in. With it enabled the USB only works with a network cable plugged in too. You have to wait for the ether to reinitialise (ether socket lights go out for a couple of secs, then come on, then the green one starts flashing) before trying to talk via the USB. The ether is initialised before config.g is run, so the IP is the one defined in platform.h. The network is disabled in this commit. The heaters are set on by 0, not 1 (i.e. Duet board v0.6 or later). To change this see #define HEAT_ON in platform.h
2013-11-26 13:38:23 +00:00
Adrian Bowyer
00a0ffd9b4
Homing against max endstop for Y (and X) implemented when there is a top
...
endstop but not a bottom one.
2013-11-25 11:03:36 +00:00
Adrian Bowyer
0670357001
Merge branch 'duet' of https://github.com/reprappro/RepRapFirmware into duet
2013-11-25 09:33:08 +00:00
Adrian Bowyer
d89b8bace0
X axis endstop now done with Z Probe (if it's activated).
2013-11-25 09:32:13 +00:00
Adrian Bowyer
d4dc6f2cfe
M84 added for Pronterface compatibility.
2013-11-23 17:17:59 +00:00
Adrian Bowyer
4c74c4eb30
Upload of reprap.htm implemented (M560). The file must end "<!-- **EoF** -->" without the quotes.
2013-11-20 22:13:23 +00:00
Adrian Bowyer
73a903e656
Fixed (I think) the M83 bug.
2013-11-20 18:47:53 +00:00
Jean-Marc Giacalone
b53832f4ce
M92 bug fixed.
2013-11-20 10:41:00 +00:00
Jean-Marc Giacalone
3b0dd0ec58
Upload of configuration file config.g implemented with M559.
2013-11-20 10:25:44 +00:00
Adrian Bowyer
c33d1ac723
M503 implemented (tis time with added bug-free-ness...)
2013-11-19 18:34:48 +00:00
Adrian Bowyer
ec5f5fe536
M503 implemented. Prints the config file to USB.
2013-11-19 16:10:53 +00:00
Adrian Bowyer
926aabe078
Added z-probe type selection. See M558.
2013-11-19 15:00:23 +00:00
Adrian Bowyer
21424714f7
File upload mechanism also now works with the web code. If we can open a user's GCode file in the Javascript this will allow web uploads. Horay! See: http://www.html5rocks.com/en/tutorials/file/dndfiles/
2013-11-18 17:40:14 +00:00
Adrian Bowyer
3dc0c7a27e
GCode file upload via USB working.
2013-11-18 15:04:32 +00:00
Adrian Bowyer
965f41e953
Shifted new M codes to start at M550. Added setting of Netmask and gateway.
2013-11-17 22:10:14 +00:00
Adrian Bowyer
104528ab66
Added user-selection of IP address via M502.
2013-11-17 17:58:30 +00:00
Adrian Bowyer
c7286905b2
Ability to specify bed Z probe points added. See M505.
2013-11-15 22:04:52 +00:00
Adrian Bowyer
4c293f767f
File printing in Marlin emulation w. Pronterface fixed.
2013-11-15 17:21:14 +00:00
Adrian Bowyer
68e0f833df
Marlin emulation implemented. Pretty much working, but not extensively tested.
2013-11-14 23:32:50 +00:00
Adrian Bowyer
bd51a7c3f0
Fixed Timer overflow bug.
2013-11-13 23:23:31 +00:00
Adrian Bowyer
8b3931c8cf
Memory diagnostics added. Mem usage is printed whenever you turn debugging on (even if it is already on).
2013-11-13 18:16:43 +00:00
Adrian Bowyer
6c22f30600
Axis angle compensation code added. Briefly tested in XY plane. Seems to work. More testing is probably needed...
2013-11-12 16:47:41 +00:00
Adrian Bowyer
b94bb6c811
Added cooling fan control.
2013-11-12 15:53:49 +00:00
Adrian Bowyer
f907e2253e
All responses to GCodes routed through a single function in the class GCodes
...
to allow the firmware to emulate how other firmware (e.g. Marlin) responds. Emulation not yet implemented, but should now be easy.
2013-11-11 17:39:17 +00:00
Adrian Bowyer
971fed0d02
Temperature range checking added (see Configuration.h). If temps repeatedly
...
fall outside the set range, it assumes the thermistor is bust and turns off the heater.
2013-11-10 21:55:44 +00:00
Adrian Bowyer
e8eafeda22
Hooks added for (I hope) the final and complete set of all parameter-changing
...
M Codes that we will need. Network initialisation delayed until after the
config.g file is run, to allow machine name etc to be set from that.
2013-11-10 19:39:13 +00:00
Adrian Bowyer
fa9b0d1478
Fixed small bug that prevented absolute extrude moves working right.
2013-11-06 11:10:26 +00:00
Adrian Bowyer
0c7e13a73e
Current position boxes added to web interface, and polled along with temperatures.
2013-10-30 15:04:38 +00:00
Adrian Bowyer
4f703d86ec
Various minor G/M codes implemented like M0. Z start speed and acceleration reduced; they were a bit fierce before.
2013-10-29 22:27:49 +00:00
Adrian Bowyer
e1601d7b3f
Various bits of code tidying. Lookahead fixed to take account of bed transform (we can no longer assume that Z moves are strictly orthogonal to XY moves, and so their scalar product may be non-zero). All velocities are now in mm/s internally. The GCodes class is responsible for multiplying mm/min by 0.0166667.
2013-10-24 16:53:25 +01:00
Adrian Bowyer
708822a54e
A couple of tidyings and additions:
...
1. Z home now moves home, rather than just setting the coordinate.
2. Wait for temps implemented.
Also the JSON requests for the g code filelist has been temporarily commented
out in reprap.htm. It was causing the firmware to hang sometimes. To be investigated.
Machine now prints nicely...
2013-10-22 18:27:12 +01:00
Adrian Bowyer
3c901fb194
Further work on Z probing. One problem was working with a white-painted bed. Replacing that with ordinary Kapton-covered glass seems to work better. And that has allowed the debugging of the code. But the probe still does not always see the bed.
2013-10-21 23:09:21 +01:00
Adrian Bowyer
79c008d469
G31 modified to allow reporting of probe values, and setting of a Z value and threshold. (See http://reprap.org/wiki/G-code#G29-G32:_Bed_probing )
2013-10-20 22:48:26 +01:00
Adrian Bowyer
eadac593cc
Z probing now works using Jean-Marc's idea. Much better.
2013-10-19 17:38:31 +01:00
Adrian Bowyer
de96171b5d
Z probe code improved, but still not there. It now uses hysteresis to
...
track up the low-precision slope of the IR probe before measuring down
the high-precision slope near 0 mm. But this means that the probe has to
be set only a fraction of a mm higher than the nozzle itself. Also (at
the moment for safety) the code thinks Z = 0 occurs when it is actually
0.2mm. This is easy to fix when the rest is reliable.
2013-10-17 23:18:57 +01:00
Adrian Bowyer
565117cba3
Move and ancilliary classes changed to store coordinates in machine units not mm internally to avoid cumulative errors.
2013-10-17 16:30:24 +01:00
Adrian Bowyer
7966335a28
Small knockout bug in reprap.htm fixed - loading the file list didn't work
...
properly. Now seems OK.
2013-10-14 18:29:47 +01:00
Jean-Marc Giacalone
c108131a14
Disable probing in Z axis endstop check.
2013-10-09 11:47:34 +01:00
Jean-Marc Giacalone
8d92b70d0f
File list implemented. Also M201 to set axis accelerations via USB.
2013-10-08 16:33:10 +01:00
Adrian Bowyer
49e9bc29c3
G92 Implemented. Tested interactively, but not from a G Code file. Should work though.
2013-09-27 18:15:49 +01:00
Adrian Bowyer
ce76147fc3
Ethernet semi-integrated, but running its own webserver. Need to intercept
...
sends and recieves and direct them at the Webserver class.
2013-09-23 23:34:55 +01:00
emaker-11z
60c71e3a07
Configured to use standard separate library.
2013-09-23 16:23:38 +01:00
Jean-Marc Giacalone
43c208ef5b
Libraries moved to own repo. Web interface toggled by #define ETHERNET.
2013-09-21 09:56:03 +01:00
Adrian Bowyer
1d0968c615
Z probing now fully implemented, except for the physical probe itself. (I.e. it's all working, but is still on the microswitch.)
2013-09-14 15:39:17 +01:00
Adrian Bowyer
d525597ebb
Z probing being implemented under G32. Not finished yet, so don't call G32...
2013-09-13 22:33:14 +01:00
Adrian Bowyer
e3fd24ca95
Configuration file (in sys/config.g) implemented.
2013-09-05 16:10:44 +01:00
Adrian Bowyer
c4017b1019
M906 (set motor current) support added.
2013-09-02 22:56:26 +01:00
