David Crocker
2305dc27c9
Fixed cooling fan support (M106 command)
...
Fixed M106 command so that the cooling fan is controllably by PWM and
works the right way round (0 = off, 1 = on). Also added optional P
parameter to specify the value that corresponds to maximum PWM.
2014-02-25 19:39:16 +00:00
David Crocker
2b7b9fc505
Fixed error with z-homing in previous release
...
Fixed a random hang after z-homing in the previous release. Also make Z
probe temperature coefficient default to zero always, and Z probe
calibration temperature default to current bed temperature always.
2014-02-25 00:32:04 +00:00
David Crocker
92c17dede2
Various changes relating to zprobe and non-volatile data
...
1. Z-probing is now done in two stages: a fast stage at the configured
home feed rate until within 10% of the target value, then a slow stage
at 20% of that feed rate.
2. Provisional support for ultrasonic Z-probe.
3. Added calibration temperature and height temperature coefficient to Z
probe parameters.
4. Z-probe parameters and Z-probe type are now saved to flash memory so
that they survive power-off and reset cycles. Separate parameters are
retained for IR and ultrasonic probes in case both are fitted.
5. Fixed issue with doing slow Z-moves immediately after Z-homing or
probing.
2014-02-24 14:17:11 +00:00
David Crocker
fe0d5f38ee
Improved PID parameters and made them configurable
...
Implemented M301 command to get/set PID parameters. Improved the PID
parameters and made minor changes to the PID algorithm to improve PID
performance with Ormerod hot end.
2014-02-08 23:52:24 +00:00
David Crocker
2d61bba024
G32 and G92 improvements
...
1. G92 with a Z value now sets exactly that Z value even if bed
compensation is in effect.
2. If G32 is run before the Z axis is homed, the first bed probe in the
G32 sequence homes the Z axiws.
2014-02-07 23:06:20 +00:00
David Crocker
0ef9d66ff1
Doing a G30 is equivalent to homing the Z-axis
...
Now sets the axisIsHomed flag for the Z-axis when a G30 command has been
executed successfully, because that puts the Z-axis at a known height.
2014-02-05 17:50:38 +00:00
David Crocker
66c934a791
File upload improvements
...
Further increased upload speed
When uploading files, preserve comments
2014-01-30 16:24:58 +00:00
David Crocker
9edaed4ac1
Further improvements to web upload and tidy-up
...
Further improved web file upload speed
Dealt with Eclipse code analysis warnings
Made some more functions and parameters const-correct
2014-01-30 14:26:45 +00:00
David Crocker
0c47fbc923
Add movement limits
...
Remember whether each axis has been homed. Don't allow z-homing or G31
procedure unless X and Y have been homed. If axes have been homed, limit
travel to size of bed.
2014-01-29 15:30:58 +00:00
David Crocker
e227dab386
Improvements to support Matt's web interface
...
Increase incoming web gcode buffer size to 1200 chars to allow more
gcodes to be sent in each message
Include free buffer size in poll response
Include response sequence number in poll response
Implement M30 (delete file) via USB interface
Support M503 and M111 commands via web interface
2014-01-27 18:15:46 +00:00
David Crocker
bdca3b1e5d
Extend web functionality for iamburny's web interface
...
Added new fields "zprobe" and "resp" to webserver poll response
Immutable string parameters are passed as const char* not char*
Increase max number of files displayed to 42
Range-check heater parameters in incoming commands to avoid buffer
overflow if heater number is out of range
2014-01-21 21:07:21 +00:00
David Crocker
618304c021
Support for modulated IR sensor
...
Add code to support sensors that allow the IR output to be modulated, to
reduce the sensitivity to ambient IR. Use M558 P2 command to enable
sensor modulation. Also changed the sensor reading averaging code to
give more consistent z-height seeking.
2014-01-14 19:03:42 +00:00
Adrian Bowyer
14b247053f
Removed legacy support for Duet v0.4 heaters. Last commit before changes to max velocity code.
2014-01-13 15:04:00 +00:00
David Crocker
ee70ee22ed
Improve performance of SD card upload via USB
...
This change approximately doubles the speed of SD-card uploading via USB
to 2.2Mbyte/sec on the test system, provided that Pronterface has been
patched to not wait for an acknowledgement after sending each line of
g-code.
2014-01-12 16:02:49 +00:00
Adrian Bowyer
95a54f763f
Macros made so that they can call macros. Beware recursion....
2014-01-05 16:49:42 +00:00
Adrian Bowyer
387dae22cd
P parameter added to M559, so that macros can be uploaded.
2013-12-30 23:09:46 +00:00
Adrian Bowyer
f746616e8c
Workround added for bug in Pronterface (it sends 2 M24 commands on second file print). M24 is now ignored if a file
...
is actively printing.
2013-12-30 17:25:38 +00:00
Adrian Bowyer
71c1571c6c
Synchronising duet branch with the mastr branch.
2013-12-27 15:02:04 +00:00
Adrian Bowyer
be1a790c47
Added more efficient canned cycle for when all three axes are being homed.
2013-12-23 21:25:40 +00:00
Adrian Bowyer
c12ebed79c
All axis homing now done with canned cycle files.
2013-12-23 18:07:16 +00:00
Adrian Bowyer
10bf338aa4
Homeing after bed transform applied bug fixed in the duet branch. The master branch will be updated after some further testing. The problem was the X endstop. If X is homed, that stop is triggered. Homeing Y then only moves Y, and so only the Y endstop is tested. But when the transform is applied X moves slightly when Y is homed (as it should) and the X endstop stoped the movement prematurely. You will need to update the files on the SD card as well as the firmware to activate the fix.
2013-12-21 16:46:42 +00:00
Adrian Bowyer
4ed66b8b01
Experimental macro/canned-cycle on the SD implemented.
2013-12-19 23:30:23 +00:00
Adrian Bowyer
4feab9afce
Homing modified to correspond with Ian's documentation...
2013-12-19 18:53:17 +00:00
Adrian Bowyer
e9539d97f0
Added M27 response.
2013-12-18 16:51:57 +00:00
Adrian Bowyer
e2a2ccc64b
Bug whereby heaters would not restart after an M0 is received fixed.
2013-12-17 23:28:57 +00:00
Adrian Bowyer
6f275e0df1
Bug where by selecting an already selected extruder did not reply (eg "ok" to Pronterface) fixed.
2013-12-13 14:49:05 +00:00
Adrian Bowyer
cfdb9dcd89
Dud temperature count now has to reach 6 (about a second) before a heater trips out (Ian's request). Also heater reset M code (M562) added. Use that with great caution.
2013-12-11 14:11:51 +00:00
Adrian Bowyer
7215696e8b
Function added to set hypotenuse lengths for multi-axis steps. These were previously computed on initialisation, but are now re-done after every M92.
2013-12-07 18:56:56 +00:00
Adrian Bowyer
91efcc4e48
M82 changed so that it reports steps/mm when given no arguments.
2013-12-06 20:56:08 +00:00
Adrian Bowyer
2022e8ab28
Various bits of file tidying...
2013-12-05 17:24:53 +00:00
Adrian Bowyer
d29058cf9d
Bug in Z probing (the Move class had no function to return the number of probe points) fixed.
2013-12-05 13:22:01 +00:00
Adrian Bowyer
dd978290b5
Emergency stop added to the web interface (and Home All taken away, as you almost never want to home Z with the other two.) SD files tidied.
2013-12-04 15:36:26 +00:00
Adrian Bowyer
1a8ffb2d00
Second degree (ruled quadratic surface) bed plane compensation added. Probe three points to get plane compensation. Probe 4 [0 = min, 1 = max: (x0, y0), (x0, y1), (x1, y1), (x1, y0) in that order] to get second degree compensation. Also M115 print version added.
2013-12-03 14:46:28 +00:00
Adrian Bowyer
27ae5f8730
Fixed (I hope) G92 bug found by Tony.
2013-11-30 17:22:16 +00:00
Adrian Bowyer
dfbc35d369
Bug found by Tony in the offsetting code fixed (I hope).
2013-11-29 23:50:59 +00:00
Adrian Bowyer
f0b7da252b
M561 reset bed transform to identity added.
2013-11-29 10:55:43 +00:00
Adrian Bowyer
f9fe813610
Improved functionality for G30; can now be set from pre-recorded
...
measurements as well as doing live probing (automatic or manual).
2013-11-28 12:54:00 +00:00
Adrian Bowyer
409af6bb11
Manual Z probing added to G30 (see http://reprap.org/wiki/G-code ).
2013-11-28 11:57:38 +00:00
Adrian Bowyer
a4d8f41271
G31 now waits for moves to end before measuring/reporting. G30 implemented. Has argument Pn n = 0,1,2 - takes probe reading at current XY and calls them point n for the purpose of bed plane calculation. Add an S field on the last probe (i.e. when n=2 usually, though you can do them in any order) to get it to fit the bed plane.
2013-11-27 22:59:37 +00:00
Adrian Bowyer
7b9894e543
M206 implemented. This commit has the ethernet enabled and heaters set on by 1 (i.e. Duet v0.5 or below).
2013-11-26 15:12:24 +00:00
Adrian Bowyer
c0b7b4bace
Working on the ether/USB problem. The network can now be disabled (#define NETWORK in Configuration.h). With it disabled the USB works with or without a network cable plugged in. With it enabled the USB only works with a network cable plugged in too. You have to wait for the ether to reinitialise (ether socket lights go out for a couple of secs, then come on, then the green one starts flashing) before trying to talk via the USB. The ether is initialised before config.g is run, so the IP is the one defined in platform.h. The network is disabled in this commit. The heaters are set on by 0, not 1 (i.e. Duet board v0.6 or later). To change this see #define HEAT_ON in platform.h
2013-11-26 13:38:23 +00:00
Adrian Bowyer
00a0ffd9b4
Homing against max endstop for Y (and X) implemented when there is a top
...
endstop but not a bottom one.
2013-11-25 11:03:36 +00:00
Adrian Bowyer
0670357001
Merge branch 'duet' of https://github.com/reprappro/RepRapFirmware into duet
2013-11-25 09:33:08 +00:00
Adrian Bowyer
d89b8bace0
X axis endstop now done with Z Probe (if it's activated).
2013-11-25 09:32:13 +00:00
Adrian Bowyer
d4dc6f2cfe
M84 added for Pronterface compatibility.
2013-11-23 17:17:59 +00:00
Adrian Bowyer
4c74c4eb30
Upload of reprap.htm implemented (M560). The file must end "<!-- **EoF** -->" without the quotes.
2013-11-20 22:13:23 +00:00
Adrian Bowyer
73a903e656
Fixed (I think) the M83 bug.
2013-11-20 18:47:53 +00:00
Jean-Marc Giacalone
b53832f4ce
M92 bug fixed.
2013-11-20 10:41:00 +00:00
Jean-Marc Giacalone
3b0dd0ec58
Upload of configuration file config.g implemented with M559.
2013-11-20 10:25:44 +00:00
Adrian Bowyer
c33d1ac723
M503 implemented (tis time with added bug-free-ness...)
2013-11-19 18:34:48 +00:00
