Added timeout to output buffers destined for USB
Fixed bugs in thermocouple code
Reallocated thermocouple pin numbers
Made Roland mill and inkjet support conditional and normally disabled
Fixed issue with thermocouple code messing up the timekeeping system,
which was suspected of causing the network to be unreliable
Added support for M577 (thanks chrishamm)
Merged in chrishamm's changes including OutputBuffer fix, changes to
Roland pin numbers, rr_configfile support in web server, and Roland and
inkjet pin numbers moved to Pins_duet.h
Merged in wrangellboy's http response changes for compatibility with
Edge browser
Other minor changes
Merged in Dan's thermocouple support
Define serial port allocation in Pins_duet.h
Fixed some leaks of OutputBuffer objects under error conditions
The terminating newline character in a gcode response is now added in
HandleReply
Implemented F, H and R parameters to M106 command. The second fan output
on a Duet 0.8.5 now defaults to being a thermostatic fan at power up.
Improved speed of file upload to SD card
G32 is now allowed if the printer has not been homed, if there is a
bed.g file
G30 commands are no longer allowed on a delta that has not been homed
M572 parameter P (drive number) replaced by parameter D (extruder
number)
File info requests are now processed in stages to reduce impact on
printing (thanks chrishamm)
Use latest network stack and webserver modules from chrishamm (thanks
chrishamm)
Added Roland mill support (thanks RRP/chrishamm)
Added S parameter (idle timeout) to M18 ans M84 commands (thanks
chrishamm)
Moved I/O pin assignments to separate Pins.h file to more easily support
alternative hardware (thanks dnewman)
Bug fix: filament usage and % print complete figures were incorrect when
absolute extruder coordinates were used
Bug fix: file-based print estimate was occasionally returned as 'inf'
which caused the web interface to disconnect
Bug fix: M666 now flags all towers as not homed
Bug fixes to extruder pressure compensation (M572 command).
New features
============
The PWM frequency for the heated bed and for any heater used as a
chamber heater is now 10Hz for bettercompatibility with DC-AC SSRs.
The PWM frequency for fans is now configurable using the F paramete ron
the M106 command. The default is 500Hz, which gives esonable control of
fans not designed for PWM. Increase it to 25000Hz when using 4-wire PWM
fans.
When a Duet 0.8.5 board is configured or detected, the fan control is
now automatically inverted. If you previously used M106 P0 I1 in
config.g to invert it, you will need to remove that.
M579 (scale Cartesian axes) is now implemented (thanks chrishamm).
M114, M119 and M573 commands can now be executed concurrently with other
commands.
When DDA debugging is enabled, the debug output now includes all active
extruders instead of just the first two.
M408 S0 now includes the fan speeds (for PanelDue).
M119 now reports the Z probe as well as the endstop switch states.
A tool can now be defined even if a tool with the same tool number
exists already. The existing tool will be shut down and deleted.
The bed heater can now be disabled using M140 S-1 (thanks chrishamm).
The chamber heater (if present) and the endstop switch states are now
reported to the web interface (thanks chrishamm).
Increased defauklt Z prove dive height to 5mm.
Increased default PID Ki to 0.2
Bug fixes
=========
On a CoreXY machine, XY speeds were too low by a factor of sqrt(2).
On a delta machine, after running auto calibration the Z=0 height could
be slightly inaccurate, depending on the difference between the X and Z
endstop corrections
When using a non-intelligent modulated Z probe on a Duet 0.8.5, the
modulation pin number was incorrect.
The M27 (Report SD card print status) response was inverted compared to
what it should be. When in Marlin mode it now includes the "byte n/m"
field that some versions of Pronterface expect.
Cold extrusion prevention did not work - an error message was generated,
but the extruder was driven anyway.
M999 PERASE is now more reliable (thanks chrishamm).
M23, M30 and M32 commands did not work when the filename parameter
passed included an absolute path.
//A T command inside a macro file did not execute the tool change macros
files.
A memory leak occurred when a tool was deleted.
All moves are now completed before switching to CoreXY mode.
Polling requests from PanelDue were not relied to when a macro was being
executed
M667 with no parameters returned an incorrect string
Enabled gcc compiler warnings. Fixed over 100 warnings including at
least one actual and several potential bugs.
Simplified delta calibration code and added X and Y parameters to M665
command
Implemented chamber temperature commands (thanks chrishamm)
Tidied up delta auto-calibration code. We now use least squares for 3,
4, 6 or 7-factor calibration.
When doing delta calibration, if a probe offset was used to adjust the
head position when probing, use the actual head coordinates instead the
probed coordinates.
Bug fix: newline was missing at end of SD card file list sent to USB
when in Marlin emulation mode.
Bug fix: Heater average PWM report (M573) sometimes gave inaccurate
values when the S parameter was used.
Implemented rr_config web request for zpl's latest web interface
Implemented 7-factor auto calibration for delta printers
Fix bug with fileinfo calls corrupting memory
M563 can now be used to delete tools
Fixed bug: when uploading to SD card via USB the file was printed
immediately
Merged RRP's 1.04 changes in, except that the fan output is only turned
on/off for extruding/non-extruding moves if the ancilliary PWM is set to
a nonzero value
Added almost instant pause functonality
Support pause and resume macros
Support nested macros
Support zpl's web interface
Merge in zpl's web interface and network changes
Add R parameter to M105 command for PanelDue
M98 can now run macros from any SD card folder
Bug fix: M92 command would only set extruder steps/mm if either 1 or 5
extruder steps/mm was provided
Bug fix: Z-homing or bed probing when axis compensation was enabled
caused the X and Y origins to shift
We now mark drives as not homed when we disable them
File info code now supports gcode files generated by Simplify3D
Updated SD card files to latest web interface
Added more comments to config.g
Head movement commands that were in the tfree files have been moved to
the tpre files, to work better when G10 nozzle offsets are used
Added support for nozzle offsets in G10 command
Disable heater timeout if the time limit is set to zero or negative
Don't send non-error responses to the web interface unless the
corresponding command also came from the web interface
Added support for aux input from serial. Need to finish this by making
serial transmission interrupt-driven.
Increased default heater S factor to 1.0 to make it easier for users to
switch from RRP official firmware
Minor fix to move lookahead code
Added support for M570 command (set max time to hot)
M81 command now waits for moves to finish before turning power off
Other minor changes
Fixed bug that caused the cooling fan PWM frequency to be 165kHz. It is
now 25kHz.
Fan RPM is now included in the web interface status response (thanks
zpl).
Many more error messages are now reported to the web interface as well
as the USB interface.
Interrupt-driven network timer task to better cope with slow SD card
writes (thanks zpl)
Module SamNonDuePin is now used for all digital and PWM pin I/O.
1. Fixed variable name of extrusion factors in JSON status response
2. Fixed bug: changing heat sample interval no longer messes up I and D
pid factors.
3. Ensure that name of file being printed is null-terminated.
4. Removed redundant function SetStepHypotenuse.
Refactored printing to strings and web server json response handling in
preparation for adding support for LCD display via serial link
Added a timer to record how long block writes to SD card take
M301 and M304 commands to set PID parameters now take an additional S
parameter. This allows for variations in cartridge heater power and
supply voltage to be taken into account more easily.
Temperature errors are reported to the web server as well as to USB.
The Heat section of the M122 diagnostics report now shows the
accumulated PID I-term.
G90 and G91 commands now affect only the the axes, not the extruders.
Bug fix: numerous calls to strncat were being made with a 'nchars'
parameter that was larger than space available in the destination
buffer.
Bug fix: print moves received just prior to an M109 or M190 command were
not executed until after the heater had reached temperature instead of
before.
Bug fix: using G10 to set oly the active temperature caused the standby
temperature to be set to an undefined value, and vice versa
G10 can now be used to retrieve the active and standby temperatures as
well as set them
Bug fix: I and D parameters were set to incorrect values when the M301
and M304 commands were used. They also reported the incorrect values.
New T parameter added to M301 and M304 commands, to allow the I term to
be preset to a suitable value when PID kicks in
Adjusted default PID parameters for lower overshoot and less oscillation
Bug fix: when axis or bed compensation was enabled a homing move to seek
for one endstop could be prematurely terminated by another endstop
M122 command only outputs LWIP stats if debug is enabled. Prevents a
hang if no UDB cable is connected when M122 is executed.
Bug fix: when resetting, the heaters used to power up for a short time
M0 and M1 commands now turn the heaters off instead of to standby
Web server status poll response now includes the selected tool number
Fixed M122 so that diagnostics are sent to the web interface as well as
USB
Fixed M220 command to respond to speed change requests faster
Count the number of active extruders and heaters, and only send their
values to the web interface, subject to a minimum of 2 heaters and 1
extruder
Fixed bug whereby incoming gcodes were URI-decoded twice, which could
cause problems if a comment contain a % character
Fixed bug whereby M109 and M190 waited for all heaters to reach target
temperature instead of just the one involved
Fixed bug whereby files whose names contain an uppercase letter G could
not be uploaded or deleted
Increase buffer size for incoming gcodes
Removed parameter to set max PWM value in M106 command. Max PWM value is
now 255 as per recent RepRapPro change.
Changed the code that deals with dropping characters in unimportant
messages sent to USB such that we only drop characters at the end of a
line (adding ".\n" to whatever we send) or drop whole lines
Changed network startup to avoid long delay if no network cable is
connected
Enable DHCP support if IP address is configured as 0.0.0.0 (not working
yet)
Move thermistor parameters to M305, added parameter to configure series
resistance
Added B and W PID parameters
Fixed bug introduced at version 057o-dc42 that broke the G32 bed
compensation. Added the Z heights of the bed compensation points to the
information displayed by M111 S2. Simplified the code that does
Z-probing in fast and slow stages. Added function sncatf and used it to
simplify the code in several places.
Added L and H parameters to the M301 and M304 commands to allow SAM3X
ADC offsets to be corrected for. Also attempted a fix for absolute
extruder movement. - but this will still be affected by rounding error.
Removed some old binaries.
1. Fixed bug introduced at version 57r whereby axis travel limits were
not applied properly.
2. Increased maximum travel on 2nd phase of Z-probing from 1mm to 10mm
3. Added parameters R (thermistor 25C resistance) and B (thermistor
beta) to M301 command
4. Added support for M304 command with same parameters as M301 command
5. PID and thermistor parameters are now saved to flash memory
This will allow for multi extruder printing support in future pull
requests. It works fine for single extruder setups as well as the
selected head is always E0.
Implemented M301 command to get/set PID parameters. Improved the PID
parameters and made minor changes to the PID algorithm to improve PID
performance with Ormerod hot end.
