bb8a2c3ef7
Z axis min and max limits are now enforced if the axes have been homed M665 command now shows the re-calculated delta radius and tower offsets after auto-calibration Initial and final RMS errors are now shown after delta auto-calibration Pause/resume now mostly works when absolute extruder coordinates are used Doubled the maximum length of the SD card file listing that can be sent to PanelDue Implemented zpl's Network and PrintMonitor changes including M404 (thanks, zpl) Increased default maximum instantaneous speed changes Bug fix:: if M226 was used to pause the print, the resume coordinates were not set up correctly Bug fix: when changing the travel direction, the head was sometimes slowed down more than necessary Bug fix: warm-up time was not shown correctly in DuetWebControl Bug fix: extruder drive positions were always shown as 0.0 in DuetWebControl Bug fix: incorrect PID parameters were shown in response to M301 Replaced old web interface files on SD card by DuetWebControl Modified all resume.g files to set the speed when moving to the paused head coordinates
35 lines
2 KiB
Text
35 lines
2 KiB
Text
; Huxley Duo config file for dc42 Duet firmware
|
|
; Based on RepRapPro version 1.04
|
|
M111 S0 ; Debug off
|
|
M550 PMyHuxleyDuo ; Machine name (can be anything you like)
|
|
M551 Preprap ; Machine password (used for FTP access)
|
|
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0x14 ; MAC Address
|
|
M552 P0.0.0.0 ; IP address (0 = use DHCP)
|
|
M553 P255.255.255.0 ; Netmask
|
|
M554 P192.168.1.1 ; Gateway
|
|
M555 P2 ; Set output to look like Marlin
|
|
G21 ; Work in millimetres
|
|
G90 ; Send absolute coordinates...
|
|
M83 ; ...but relative extruder moves
|
|
M574 X0 Y1 Z0 S1 ; set endstop configuration (Y endstop only, at low end, active high)
|
|
M569 P0 S1 ; Reverse the X motor
|
|
M569 P3 S0 ; Don't reverse the extruder motor
|
|
M906 X600 Y600 Z600 E600 ; Set motor currents (mA)
|
|
M305 P0 T100000 R4700 ; bed thermistor is 100K with 4K7 series resistor
|
|
M305 P1 R4700 ; first nozzle thermistor has 4K7 series resistor
|
|
M305 P2 R4700 ; second nozzle thermistor has 4K7 series resistor
|
|
M92 E660 ; Set extruder steps per mm
|
|
M558 P2 ; Use a modulated Z probe (change to P1 if you have a dc42 diff IR zprobe)
|
|
G31 Z0.6 P550 ; Set the probe height and threshold (deliberately too high to avoid bed crashes on initial setup)
|
|
M556 S78 X0 Y0 Z0 ; Put your axis compensation here
|
|
M201 X3000 Y3000 Z150 E500 ; Accelerations (mm/s^2)
|
|
M203 X15000 Y15000 Z100 E3600 ; Maximum speeds (mm/min)
|
|
M566 X200 Y200 Z30 E20 ; Maximum jerk rates mm/minute
|
|
M563 P0 D0 H1 ; Define tool 0
|
|
G10 P0 S-273 R-273 ; Set tool 0 operating and standby temperatures
|
|
;M563 P1 D1 H2 ; Define tool 1 Uncomment if you have a dual colour upgrade
|
|
;G10 P1 X19 S-273 R-273 ; Set tool 1 operating and standby temperatures Uncomment if you have a dual colour upgrade
|
|
M208 X130 Y138 Z95 ; set axis maxima (adjust to suit your machine)
|
|
M208 X-13 Y-4 Z-0.5 S1 ; set axis minim (adjust to make X=0 and Y=0 the edge of the bed after homing)
|
|
;
|
|
T0 ; select first hot end
|