47 lines
3.2 KiB
Text
47 lines
3.2 KiB
Text
; Ormerod 1 config file for dc42 Duet firmware
|
|
M111 S0 ; Debug off
|
|
M550 PMy Ormerod ; Machine name (can be anything you like)
|
|
M551 Preprap ; Machine password (currently not used)
|
|
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address
|
|
;*** Adjust the IP address and gateway in the following 2 lines to suit your network
|
|
M552 P0.0.0.0 ; IP address (0 = use DHCP)
|
|
M554 P192.168.1.1 ; Gateway
|
|
M553 P255.255.255.0 ; Netmask
|
|
M555 P2 ; Set output to look like Marlin
|
|
M575 P1 B57600 S1 ; Comms parameters for PanelDue
|
|
|
|
G21 ; Work in millimetres
|
|
G90 ; Send absolute coordinates...
|
|
M83 ; ...but relative extruder moves
|
|
M574 X0 Y2 Z0 S1 ; set endstop configuration (Y endstop only, at high end, active high)
|
|
M92 X87.4890 Y87.4890 Z4000 ; Set axis steps/mm
|
|
M906 X800 Y1000 Z800 E800 ; Set motor currents (mA)
|
|
M563 P0 D0 H1 ; Define tool 0
|
|
G10 P0 S0 R0 ; Set tool 1 operating and standby temperatures
|
|
M92 E420 ; Set extruder steps per mm (single nozzle)
|
|
;*** If you have a dual-nozzle build, remove or comment out the previous line, and un-comment the following 3 lines
|
|
;M563 P1 D1 H2 ; Define tool 1
|
|
;G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures
|
|
;M92 E420:420 ; Set extruder steps/mm (dual nozzle)
|
|
;*** If you have a modulated IR probe without on-board microcontroller, change P1 to P2 in the following
|
|
M558 P1 ; Use an unmodulated Z probe or an intelligent Z probe
|
|
G31 Z1.20 P500 ; Set the probe height and threshold (put your own values here)
|
|
;*** If you have a Duet board with 4.7K thermistor series resistors, change R1000 to R4700 to the following M305 commands
|
|
M305 P0 R1000 H0 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction
|
|
M305 P1 R1000 H0 L0 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction
|
|
M305 P2 R1000 H0 L0 ; Put your own H and/or L values here to set the second nozzle thermistor ADC correction
|
|
;*** Adjust the XY coordinates in the following M557 commands to suit your build and the position of the IR sensor
|
|
M557 P0 X60 Y0 ; Four...
|
|
M557 P1 X60 Y165 ; ...probe points...
|
|
M557 P2 X222 Y165 ; ...for bed...
|
|
M557 P3 X222 Y0 ; ...levelling
|
|
;M557 P4 X141 Y82.5 ; 5th probe point for levelling (un-comment this if you are using a dc42 differential IR probe)
|
|
;*** if you are using axis compensation, put the figures in the following command
|
|
M556 S78 X0 Y0 Z0 ; Axis compensation here
|
|
M201 X800 Y800 Z15 E1000 ; Accelerations (mm/s^2)
|
|
M203 X15000 Y15000 Z100 E3600 ; Maximum speeds (mm/min)
|
|
M566 X600 Y600 Z30 E20 ; Minimum speeds mm/minute
|
|
M208 X214 Y210 Z200 ; set axis maxima (adjust to suit your machine)
|
|
M208 X-8 Y0 Z-1 S1 ; set axis minimum (adjust to make X=0 the edge of the bed)
|
|
;
|
|
T0 ; select first hot end
|