bb8a2c3ef7
Z axis min and max limits are now enforced if the axes have been homed M665 command now shows the re-calculated delta radius and tower offsets after auto-calibration Initial and final RMS errors are now shown after delta auto-calibration Pause/resume now mostly works when absolute extruder coordinates are used Doubled the maximum length of the SD card file listing that can be sent to PanelDue Implemented zpl's Network and PrintMonitor changes including M404 (thanks, zpl) Increased default maximum instantaneous speed changes Bug fix:: if M226 was used to pause the print, the resume coordinates were not set up correctly Bug fix: when changing the travel direction, the head was sometimes slowed down more than necessary Bug fix: warm-up time was not shown correctly in DuetWebControl Bug fix: extruder drive positions were always shown as 0.0 in DuetWebControl Bug fix: incorrect PID parameters were shown in response to M301 Replaced old web interface files on SD card by DuetWebControl Modified all resume.g files to set the speed when moving to the paused head coordinates
58 lines
3.2 KiB
Text
58 lines
3.2 KiB
Text
; Configuration file for Mini Kossel kit from Think3DPrint3D
|
|
|
|
; Communication and general
|
|
M111 S0 ; Debug off
|
|
M550 PMiniKossel ; Machine name and Netbios name (can be anything you like)
|
|
M551 Preprap ; Machine password (used for FTP)
|
|
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address
|
|
;*** Adjust the IP address and gateway in the following 2 lines to suit your network
|
|
M552 P0.0.0.0 ; IP address (0 = use DHCP)
|
|
M554 P192.168.1.1 ; Gateway
|
|
M553 P255.255.255.0 ; Netmask
|
|
M555 P2 ; Set output to look like Marlin
|
|
G21 ; Work in millimetres
|
|
G90 ; Send absolute coordinates...
|
|
M83 ; ...but relative extruder moves
|
|
|
|
; Axis and motor configuration
|
|
M569 P0 S1 ; Drive 0 goes forwards
|
|
M569 P1 S1 ; Drive 1 goes forwards
|
|
M569 P2 S1 ; Drive 2 goes forwards
|
|
M569 P3 S1 ; Drive 3 goes forwards
|
|
M569 P4 S1 ; Drive 4 goes forwards
|
|
M574 X2 Y2 Z2 S1 ; set endstop configuration (all endstops at high end, active high)
|
|
;*** The homed height is deliberately set too high in the following - you will adjust it during calibration
|
|
M665 R105.6 L215.0 B85 H240 ; set delta radius, diagonal rod length, printable radius and homed height
|
|
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
|
|
M92 X80 Y80 Z80 ; Set axis steps/mm
|
|
M906 X1000 Y1000 Z1000 E500 ; Set motor currents (mA)
|
|
M201 X1000 Y1000 Z1000 E1000 ; Accelerations (mm/s^2)
|
|
M203 X20000 Y20000 Z20000 E3600 ; Maximum speeds (mm/min)
|
|
M566 X1200 Y1200 Z1200 E1200 ; Maximum instant speed changes mm/minute
|
|
|
|
; Thermistors
|
|
;*** If you have a Duet board stickered "4.7K", change R1000 to R4700 to the following M305 commands
|
|
M305 P0 T100000 B3950 R1000 H30 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction
|
|
M305 P1 T100000 B3974 R1000 H30 L0 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction
|
|
M305 P2 T100000 B3974 R1000 H30 L0 ; Put your own H and/or L values here to set the second nozzle thermistor ADC correction
|
|
M570 S180 ; Hot end may be a little slow to heat up so allow it 180 seconds
|
|
|
|
; Tool definitions
|
|
M563 P0 D0 H1 ; Define tool 0
|
|
G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures
|
|
;*** If you have a dual-nozzle build, un-comment the next 2 lines
|
|
;M563 P1 D1 H2 ; Define tool 1
|
|
;G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures
|
|
M92 E663:663 ; Set extruder steps per mm
|
|
|
|
; Z probe and compensation definition
|
|
;*** If you have an IR zprobe instead of a switch, change P4 to P1 in the following M558 command
|
|
M558 P4 X0 Y0 Z0 ; Z probe is a switch and is not used for homing any axes
|
|
G31 X0 Y0 Z4.80 P500 ; Set the zprobe height and threshold (put your own values here)
|
|
|
|
;*** If you are using axis compensation, put the figures in the following command
|
|
M556 S78 X0 Y0 Z0 ; Axis compensation here
|
|
|
|
M208 S1 Z-0.2 ; set minimum Z
|
|
;
|
|
T0 ; select first hot end
|