58 lines
3.2 KiB
Text
58 lines
3.2 KiB
Text
; Configuration file for Mini Kossel kit from Think3DPrint3D
|
|
|
|
; Communication and general
|
|
M111 S0 ; Debug off
|
|
M550 PMiniKossel ; Machine name and Netbios name (can be anything you like)
|
|
M551 Preprap ; Machine password (used for FTP)
|
|
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address
|
|
;*** Adjust the IP address and gateway in the following 2 lines to suit your network
|
|
M552 P0.0.0.0 ; IP address (0 = use DHCP)
|
|
M554 P192.168.1.1 ; Gateway
|
|
M553 P255.255.255.0 ; Netmask
|
|
M555 P2 ; Set output to look like Marlin
|
|
G21 ; Work in millimetres
|
|
G90 ; Send absolute coordinates...
|
|
M83 ; ...but relative extruder moves
|
|
|
|
; Axis and motor configuration
|
|
M569 P0 S1 ; Drive 0 goes forwards
|
|
M569 P1 S1 ; Drive 1 goes forwards
|
|
M569 P2 S1 ; Drive 2 goes forwards
|
|
M569 P3 S1 ; Drive 3 goes forwards
|
|
M569 P4 S1 ; Drive 4 goes forwards
|
|
M574 X2 Y2 Z2 S1 ; set endstop configuration (all endstops at high end, active high)
|
|
;*** The homed height is deliberately set too high in the following - you will adjust it during calibration
|
|
M665 R105.6 L215.0 B85 H240 ; set delta radius, diagonal rod length, printable radius and homed height
|
|
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
|
|
M92 X80 Y80 Z80 ; Set axis steps/mm
|
|
M906 X1000 Y1000 Z1000 E500 I60 ; Set motor currents (mA) and increase idle current to 60%
|
|
M201 X1000 Y1000 Z1000 E1000 ; Accelerations (mm/s^2)
|
|
M203 X20000 Y20000 Z20000 E3600 ; Maximum speeds (mm/min)
|
|
M566 X1200 Y1200 Z1200 E1200 ; Maximum instant speed changes mm/minute
|
|
|
|
; Thermistors
|
|
;*** If you have a Duet board stickered "4.7K", change R1000 to R4700 to the following M305 commands
|
|
M305 P0 T100000 B3950 R1000 H30 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction
|
|
M305 P1 T100000 B3974 R1000 H30 L0 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction
|
|
M305 P2 T100000 B3974 R1000 H30 L0 ; Put your own H and/or L values here to set the second nozzle thermistor ADC correction
|
|
M570 S180 ; Hot end may be a little slow to heat up so allow it 180 seconds
|
|
|
|
; Tool definitions
|
|
M563 P0 D0 H1 ; Define tool 0
|
|
G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures
|
|
;*** If you have a dual-nozzle build, un-comment the next 2 lines
|
|
;M563 P1 D1 H2 ; Define tool 1
|
|
;G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures
|
|
M92 E663:663 ; Set extruder steps per mm
|
|
|
|
; Z probe and compensation definition
|
|
;*** If you have an IR zprobe instead of a switch, change P4 to P1 in the following M558 command
|
|
M558 P4 X0 Y0 Z0 ; Z probe is a switch and is not used for homing any axes
|
|
G31 X0 Y0 Z4.80 P500 ; Set the zprobe height and threshold (put your own values here)
|
|
|
|
;*** If you are using axis compensation, put the figures in the following command
|
|
M556 S78 X0 Y0 Z0 ; Axis compensation here
|
|
|
|
M208 S1 Z-0.2 ; set minimum Z
|
|
;
|
|
T0 ; select first hot end
|