51 lines
2.6 KiB
Text
51 lines
2.6 KiB
Text
; Configuration file for RepRapPro Fisher - delta 3D printer
|
|
|
|
; Communication and general
|
|
M111 S0 ; Debug off
|
|
M550 PRepRapProFisher1 ; Machine name (can be anything you like)
|
|
M551 Preprap ; Machine password (used for FTP)
|
|
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0x43 ; MAC Address
|
|
;*** Adjust the IP address and gateway in the following 2 lines to suit your network
|
|
M552 P0.0.0.0 ; IP address
|
|
;M554 P192.168.1.1 ; Gateway
|
|
M553 P255.255.255.0 ; Netmask
|
|
M555 P2 ; Set output to look like Marlin
|
|
G21 ; Work in millimetres
|
|
G90 ; Send absolute coordinates...
|
|
M83 ; ...but relative extruder moves
|
|
|
|
; Axis and motor configuration
|
|
M569 P0 S1 ; Drive 0 goes forwards
|
|
M569 P1 S1 ; Drive 1 goes forwards
|
|
M569 P2 S1 ; Drive 2 goes forwards
|
|
M569 P3 S1 ; Drive 3 goes forwards
|
|
M569 P4 S1 ; Drive 4 goes forwards
|
|
M574 X2 Y2 Z2 S1 ; set endstop configuration (all endstops at high end, active high)
|
|
;*** The homed height is deliberately set too high in the following - you will adjust it during calibration
|
|
M665 R81.0 L160.0 B75 H169 ; set delta radius, diagonal rod length, printable radius and homed height
|
|
M666 X0.0 Y0.0 Z0.0 ; put your endstop adjustments here
|
|
M92 X87.489 Y87.489 Z87.489 ; Set axis steps/mm
|
|
M906 X800 Y800 Z800 E1000 ; Set motor currents (mA)
|
|
M201 X4000 Y4000 Z4000 E4000 ; Accelerations (mm/s^2)
|
|
M203 X15000 Y15000 Z15000 E9000 ; Maximum speeds (mm/min)
|
|
M210 Z50 ; Homing feedrate
|
|
M566 X1200 Y1200 Z1200 E1200 ; Maximum instant speed changes mm/minute
|
|
|
|
; Thermistors
|
|
M305 P1 R4700
|
|
|
|
; Tool definitions
|
|
M140 H-1 ; Disable heatbed
|
|
M563 P0 D0 H1 ; Define tool 0
|
|
G10 P0 S210 R-273 ; Set tool 0 operating and standby temperatures
|
|
M301 H1 P12 I0.4 D80 W180 B300 ; Set tool 0 PID parameters
|
|
M92 E310 ; Set to 137 for direct drive. Set extruder steps per mm
|
|
|
|
;// Z probe and compensation definition
|
|
;*** If you have an IR zprobe instead of a switch, change P4 to P1 in the following M558 command
|
|
M558 P4 X0 Y0 Z0 H4 ; Z probe is a switch and is not used for homing any axes
|
|
G31 X0 Y0 Z-0.1 P200 ; Set the zprobe height and threshold (put your own values here)
|
|
|
|
;*** If you are using axis compensation, put the figures in the following command
|
|
M556 S78 X0 Y0 Z0 ; Axis compensation here
|
|
|