/**
 * \file
 *
 * \brief EMAC (Ethernet MAC) driver for SAM.
 *
 * Copyright (c) 2011-2012 Atmel Corporation. All rights reserved.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an
 *    Atmel microcontroller product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 * \asf_license_stop
 *
 */



#ifndef CONF_EMAC_H_INCLUDED
#define CONF_EMAC_H_INCLUDED

#include "Arduino.h"

/** EMAC PHY address */
#define BOARD_EMAC_PHY_ADDR  2
/*! EMAC RMII mode */
#define BOARD_EMAC_MODE_RMII 1

// dc42, 2014-06-01.
// The following #defines are not used, so I have commented them out.
// The ones in hardware/arduino/sam/system/libsam/source/emac.c get used instead, and they need to be changed to these values (32 and 8).

/** Number of buffer for RX */
//#define EMAC_RX_BUFFERS  (32)

/** Number of buffer for TX */
//#define EMAC_TX_BUFFERS  (8)


/** MAC PHY operation max retry count */
#define MAC_PHY_RETRY_MAX 1000000

/** MAC address definition.  The MAC address must be unique on the network. */
#define ETHERNET_CONF_ETHADDR0                        0xBE
#define ETHERNET_CONF_ETHADDR1                        0xEF
#define ETHERNET_CONF_ETHADDR2                        0xDE
#define ETHERNET_CONF_ETHADDR3                        0xAD
#define ETHERNET_CONF_ETHADDR4                        0xFE
#define ETHERNET_CONF_ETHADDR5                        0xED

/** WAN Address: 192.168.0.2 */
/* The IP address being used. */
//*******************************************************************************************
// Commented out by AB - see ethernet_sam.c

//#define ETHERNET_CONF_IPADDR0                         192
//#define ETHERNET_CONF_IPADDR1                         168
//#define ETHERNET_CONF_IPADDR2                         1
//#define ETHERNET_CONF_IPADDR3                         14
//
///** WAN gateway: 192.168.0.1 */
///** The gateway address being used. */
//#define ETHERNET_CONF_GATEWAY_ADDR0                   192
//#define ETHERNET_CONF_GATEWAY_ADDR1                   168
//#define ETHERNET_CONF_GATEWAY_ADDR2                   1
//#define ETHERNET_CONF_GATEWAY_ADDR3                   1
//
///** The network mask being used. */
//#define ETHERNET_CONF_NET_MASK0                       255
//#define ETHERNET_CONF_NET_MASK1                       255
//#define ETHERNET_CONF_NET_MASK2                       255
//#define ETHERNET_CONF_NET_MASK3                       0

//********************************************************************************************

/** Ethernet MII/RMII mode */
#define ETH_PHY_MODE  BOARD_EMAC_MODE_RMII

#endif /* CONF_EMAC_H_INCLUDED */