Added F (probing speed) and T (travel speed) parameters to M558 command
Removed M210 command because home feed rates are defined in the homing
files
Increased UART interrupt priority to avoid dropping characters sent by
PanelDue
Bug fix: M558 P3 did not leave the Z probe control pin high
Bug fix: in version 1.09j only, the move following a G92 E0 command was
sometimes executed from an incorrect start point
Fixed bugs with reads/writes from/to the SD card that spanned one or
more whole sectors
Updated to latest Atmel HSMCI driver
Bug fix: Pause function sometimes used to hang while running pause macro
file
Don't wait for all moved to complete when executing a G92 command that
just resets extruder positions
M574 endstop configuration now overrides M558 when determining whether
or not to use the Z probe instead of a homing switch
Added XYZ parameters to M667 command to support CoreXZ etc. machines
with paired axis ratios that are not 1:1
Minor change to step ISR to improve timings and service drives in
round-robin order
Added support for Duet 0.8.5 with auto detection between 0.6 and 0.85
board types
Added P parameter to M115 command to set board type
Changed M115 output to report the board type that was configured or
auto-detected
Improved ISR and step pulse generation efficiency to allow higher
movement speeds, especially wheh using 0.9deg/step motors
Added XYZE parameters to M569 command to allow driver remapping
Added R parameter to M569 command to allow enable signal to be reversed
when using external drivers (thanks dnewman)
Removed M558 R parameter because boare type 0.7 can now be set via M115
instead
Moved Fan0 RPM sense pin to PA14 to avoid conflict with Duet 0.8.5 FAN1
pin
M408 poll command can now be handled concurrently with other commands
Fixed print quality problems that mostly affected delta printers e.g. on
spiral vase cylinder
When reconnecting a browser, cancel any file upload from the same IP
address
M111 now prints the number of each module with debugging enabled or
disabled
In special moves on delta printers, the F parameter is now interpreted
as the speed of the tower that moves the most
M114 now reports stepper positions as well as head position
Default to output in Marlin mode
M104 command defaults to the only tool if there is only one tool and it
is not selected
Trying different code for M999PERASE command to see if we can get it to
unlock flash and reset more reliably
When step errors are logged, report them immediately if Move debugging
is enabled. Also reports the total number of step errors in M122.
Changed interrupt priority to make tick interrupt higher priority than
step interrupt, because we rely on the tick interrupt to check for over
temperature conditions and kick the watchdog
Fixed CoreXY homing bug
Support simultaneous XY homing on CoreXY printers
Updated sample homeall.g file for CoreXY printers to do simultaneous XY
homing
Added H (height correction) parameter to G30 command
G30 S-1 now reports trigger height without changing ZS origin
Added M665 Z parameter to better support square delta printers
Changed interrupt priorities to make step pulse timing interrupt higher
priority than Ethernet (thanks zpl)
Enabled gcc compiler warnings. Fixed over 100 warnings including at
least one actual and several potential bugs.
Simplified delta calibration code and added X and Y parameters to M665
command
Implemented chamber temperature commands (thanks chrishamm)
Fixed two potential divide by zero errors in PrintMonitor
Don't report an error if tpre, tpost or tfree macro file is not found
Changed the way we report bed height errors after bed probing without
calibration
Final Z probing speed is now always 1/3 of the initial probing speed as
set by M210
Bug fix: after Z probing the Z height was set incorrectly by 1 motor
microstep
Z axis min and max limits are now enforced if the axes have been homed
M665 command now shows the re-calculated delta radius and tower offsets
after auto-calibration
Initial and final RMS errors are now shown after delta auto-calibration
Pause/resume now mostly works when absolute extruder coordinates are
used
Doubled the maximum length of the SD card file listing that can be sent
to PanelDue
Implemented zpl's Network and PrintMonitor changes including M404
(thanks, zpl)
Increased default maximum instantaneous speed changes
Bug fix:: if M226 was used to pause the print, the resume coordinates
were not set up correctly
Bug fix: when changing the travel direction, the head was sometimes
slowed down more than necessary
Bug fix: warm-up time was not shown correctly in DuetWebControl
Bug fix: extruder drive positions were always shown as 0.0 in
DuetWebControl
Bug fix: incorrect PID parameters were shown in response to M301
Replaced old web interface files on SD card by DuetWebControl
Modified all resume.g files to set the speed when moving to the paused
head coordinates
Merged in zpl's latest changes to Network and Print Monitor modules,
providing DHCP and Netbios name support
Added command M999 S4321 to unlock flash memory, reset and boot to BOSSA
port
Z dive height is now relative to Z probe trigger height and default is
reduced to 3mm
Added experimental support for acoustic probe for delta printers
Bug fix: firmware once again prevents Z homing before X and Y are homed,
if the Z probe is used for Z homing
Various code tidying
Speed factor and extrusion factor changes now take effect 1 move earlier
Default feed rate after reset increased to 3000mm/min
M574 command now accepts E parameter to that active low Z probe switches
can be used
Bed compensation is cancelled if Z probe was already triggered at the
start of a probe
M20 S2 response now flags directories with a * prefix
M408 command introduced as an alternative to M105 S2 and M105 S3
When cold extrusion is prevented, say which tool was affected in the
error message
Bug fix: if a drive was turned off manually after going into idle mode,
when it was enabled again the current remained at 30%
Bug fix: cold extrusion prevention did not work
Tidied up delta auto-calibration code. We now use least squares for 3,
4, 6 or 7-factor calibration.
When doing delta calibration, if a probe offset was used to adjust the
head position when probing, use the actual head coordinates instead the
probed coordinates.
Bug fix: newline was missing at end of SD card file list sent to USB
when in Marlin emulation mode.
Bug fix: Heater average PWM report (M573) sometimes gave inaccurate
values when the S parameter was used.
Implemented rr_config web request for zpl's latest web interface
Implemented 7-factor auto calibration for delta printers
Fix bug with fileinfo calls corrupting memory
M563 can now be used to delete tools
Fixed bug: when uploading to SD card via USB the file was printed
immediately
Merged RRP's 1.04 changes in, except that the fan output is only turned
on/off for extruding/non-extruding moves if the ancilliary PWM is set to
a nonzero value
Add R parameter to M552 command to allow HTTP port to be configured
When listing SD card files, ignore files with a leading '.' in the
filename (e.g. files that Mac computers add to store metadata)
Merged zpl's changes for binary file uploading and PrintMonitor
Fixed bug with filament-based print time estimation
Fixed bug that caused feed rate to often not be restored after running
a macro
Print Z probe offsets at end of G32 sequence if Move debug is enabled
Prevent setting of absurdly high hot end temperatures
Added R parameter to G1 to go back to previous location, with optional
offsets
Allow Pronterface and PanelDue M105 requests to execute during file
macros etc.
Added more status information for PanelDue to M105 S2 command
Send replies when prints are paused, resumed or cancelled
Added missing newlines at end of M105 responses
Increased X and Y course homing speeds
Fixed bug with reading file info
Don't return status as Printing if just running a macro
Restored Json buffer back to 2000 bytes so as to return more files on SD
card
Limit the amount of moves we buffer so as to react faster to speed and
extrusion rate changes
Return print time left estimates in M105 S2 status response if printing
a file
Show stepper motor currents as integers and do some rounding to get more
accurate values
Added almost instant pause functonality
Support pause and resume macros
Support nested macros
Support zpl's web interface
Merge in zpl's web interface and network changes
Add R parameter to M105 command for PanelDue
M98 can now run macros from any SD card folder
Fixed G32 so that it really does run macro file bed.g if it exists
Added H parameter to M558 command
Added bed.g file for Mini Kossel with mechanical Z probe
Added M575 command to set baud rate and whether or not checksums are
required.
Default aux baud rate is now 57600.
Added support for a Z probe switch connected to the E0 endstop pins.
Added "geometry" variable in M105 S3 status response.
Fixes some possible issues in delta printing code
Don't apply Z probe XY correction when probing at current point with G30
with a P parameter
Added experimental simulation code, controlled by M37 for now
Added X and Y z-probe offsets to G31 command
Reworked G31 and G32 to do less work in the step ISR and to support Z
probe on delta printers
Z probe modulation pin is now selected using M558 R parameter instead of
probe type
Incorporated zpl's Network module updates and some of his Gcodes updated
Merged RRP's 0.96 Move code into mine
Added M105 S3, M20 S2 and M36 commands for supporting TFT control panel
Added X parameter to M305 command to allow thermistor channels to be
changed
Removed space after "B:" in M105 response to avoid confusing Pronterface
M0 no longer turns motors off
Updated M18 and M84 as per zpl fork
Don't insist that user provides values for all 5 possible extruders in
M906 command
Added Ormerod 2 sys files
Updated web interface files
Bug fix: M92 command would only set extruder steps/mm if either 1 or 5
extruder steps/mm was provided
Bug fix: Z-homing or bed probing when axis compensation was enabled
caused the X and Y origins to shift
We now mark drives as not homed when we disable them
File info code now supports gcode files generated by Simplify3D
Updated SD card files to latest web interface
Added more comments to config.g
Head movement commands that were in the tfree files have been moved to
the tpre files, to work better when G10 nozzle offsets are used
Added support for nozzle offsets in G10 command
Disable heater timeout if the time limit is set to zero or negative
Don't send non-error responses to the web interface unless the
corresponding command also came from the web interface
Added support for aux input from serial. Need to finish this by making
serial transmission interrupt-driven.
Increased default heater S factor to 1.0 to make it easier for users to
switch from RRP official firmware
Minor fix to move lookahead code
Added support for M570 command (set max time to hot)
M81 command now waits for moves to finish before turning power off
Other minor changes
Fixed bug that caused the cooling fan PWM frequency to be 165kHz. It is
now 25kHz.
Fan RPM is now included in the web interface status response (thanks
zpl).
Many more error messages are now reported to the web interface as well
as the USB interface.
Interrupt-driven network timer task to better cope with slow SD card
writes (thanks zpl)
Module SamNonDuePin is now used for all digital and PWM pin I/O.
1. Fixed variable name of extrusion factors in JSON status response
2. Fixed bug: changing heat sample interval no longer messes up I and D
pid factors.
3. Ensure that name of file being printed is null-terminated.
4. Removed redundant function SetStepHypotenuse.
Fixed combined xyz move bug (thanks zpl). Reversed default direction of
X motor. Added support for M569 command. Fixed bug in execution of M503
command via web interface.
Refactored printing to strings and web server json response handling in
preparation for adding support for LCD display via serial link
Added a timer to record how long block writes to SD card take
Changed compiler optimization option to -O2 (was accidentally reset to
-Os in previous release)
Set the number of decimal places reported in the responses to various M
commands
Integrated zpl's changes to returning lists of files, returning info for
file being printed, and some network layer changes
Fixed bug: if 5 point bed compansation was used then doing G32 more than
once would try to move the head off the edge of the bed unless the first
4 probe coordinates were reset between them.
Fixed bug: if the last command in a a macro file did not end in newline
then it might not be fully executed
Bug fix: potential array underrun in Gcodes::Pop()
Reduced Z dive height back to 5mm
M563 command extended to allow the tool number origin to be adjusted. If
there is no P parameter in the command then the S parameter specifies an
offset to be added to tool numbers in T, G10, M104 and M109 commands.
This is so that multi-media gcode files generated by slic3r can be
printed without having to edit all the tool numbers in the gcode file
first. This extension is intended to be temporary, until slicer provides
a mechanism for specifying the tool numbers. A separate offset is
maintained for each data source (USB, web or SD card) and the offset for
data from the SD card is reset to zero when a new file is started. To
use this facility to print slic3r multi-media gcode files, add M563 S1
to your start gcode.
M104 and M109 commands now accept an optional T parameter to specify the
tool number, as generated by slic3r in multi-media gcode files.
Movement code from RepRapPro's dev branch incorporated, including
5-point manual or automatic bed compensation mechanism.
Heater status (off/standby/on) is included in the status poll response
for the web interface. This will be used in a future version of the web
interface.
Incorporated code from RepRapPro dev branch to allow many more
M-commands to return values as well as set them.
Incorporated code from RepRapPro dev branch to implement the M119 and
M135 commands. There is currently a bug in the M135 (set heat sample
interval) command, which means that if you change the interval from its
default value of 0.5 seconds then you need to adjust the I parameter by
the same ratio and the D parameter by the inverse ratio.
Extrusion totals are reset to zero when starting a new print from SD
card.
M301 and M304 commands to set PID parameters now take an additional S
parameter. This allows for variations in cartridge heater power and
supply voltage to be taken into account more easily.
Temperature errors are reported to the web server as well as to USB.
The Heat section of the M122 diagnostics report now shows the
accumulated PID I-term.
G90 and G91 commands now affect only the the axes, not the extruders.
Bug fix: numerous calls to strncat were being made with a 'nchars'
parameter that was larger than space available in the destination
buffer.
Bug fix: print moves received just prior to an M109 or M190 command were
not executed until after the heater had reached temperature instead of
before.
