Bed compensation taper is now applied to 3/4/5-point compensation
methods too
Recognise generated-with comment in new Cura gcode files
Recognise filament-used info min new kisslicer files
When uploading files, create the full path if necessary
Duet 0.8.5 webserver looks for gzipped files first
A second controlled fan on the Duet 0.6 is no longer inverted
Renamed function Network::IPAddress to GetIPAddress to avoid clash with
IPAddress class used in DuetEthernet build
Duet 0.8.5 web server now looks for a gzipped version of the file is a
web file was not found
Duet 0.8.5 web server only returns a 404 page of the file that was not
found was a .html or .htm file
- Added support for M374 (save height map) and M375 (load height map)
- Added M376 (set bed compensation taper height)
- Added T parameter to G31 command
- M500, M501 and M502 now use config_override.g instead of flash memory.
The parameters saved and restored are:
-- M307 auto tune results
-- PID parameters, if you used M301 to override the auto tune PID
settings
-- Delta printer M665 and M666 settings
-- G31 trigger height, trigger value and X and Y offsets
- The M501 auto save option has been removed
- Removed S and T parameters from M301 command. Use M307 command
instead.
- M301 with negative P parameter no longer sets bang-bang mode. Use M307
instead.
- Added P parameter to the G31 command to specify Z probe type. This
allows you to view the parameters for the Z probe(s) and to set
parameters for a particular Z probe type without selecting that type.
G31 P or G31 P0 prints the parameters of the currently-selected Z probe.
- Z probe offsets are now applied during G30 probing with specified XY
coordinates, including during delta auto calibration
- Z probe recovery time is now applied from the end of the travel move
just before probing
- Fixed bad dive height when using G29 with a large trigger height
- Fixed bad JSON message during printing when there were no active
extruders
- Added exception handlers and store a software reset code when an
exception occurs
- Fixed reset reason text because on the Duet WiFi a watchdog reset can
look like an external reset
- G30 S-1 how printes the stopped height
- Implemented M401 and M402
Support concurrenrt execution of commands form different channels
M143 now supports individual temperature limits per heater
Fixed issue with dely of up to 2 seconds when switching Duet WiFi heater
channel 3 to servo mode
When enable polarity is set using the M569 R parameter, disable the
corresponding drive
Add exdperimental S99 option on G1 command to log probe changes (Duet
WiFi only)
Support R and S parameters in M109 and M190 as Marlin does
Added support for M191
Added support for Steinhart-Hart C parameter
Thermistor disconnected threshold now depends on thermistor parameters
Added I parameter in M280 command
Added diagnostic test (M122 S101) for SX1509B chip on Duet WiFi
expansion boards
Heaters driven from TC channels on Duet WiFi no longer glitch on for a
short while after reset
Bug fix: M280 S-1 was ignoring inverted output status
Bug fix: if there were too many files in the /gcodes folder then AJAX
errors occurred (thanks chrishamm)
Fixed several bugs in file time stamping
Fixed M280 and M42 commands using unused heaster channels on Duet 0.6
and 0.8.5
Reduced the amount of I2C traffic, by using DueX5 interrupt line to tell
if new data is available and by only sending fan PWM values when they
change
Display TMC2660 driver status and DueX2/X5 stall status in M122 response
Removed E parameter from M574 command (use M558 I parameter instead)
Fixed response to M307 with H parameter only
Added DueX2/DueX5 support
Report expansion board type in electronics string
Added Z probe type 6 (switch on E1 stop)
Support heater 6 on Duet 0.8.5 (untested, probably incomplete)
Changed M42 pin numbering, see duet3d.com wiki
Added M280 servo support
Allow separate firmware un-retract speed to be configured in M207
Allow negative extra un-retraction in M207
Allow dans ot be disabled yusing M106 P# I-1. They can then be used as
general-purpose pins (m42) or servos (M280).
Removed support for Duet WiFi prototype 1 board
Support expanson pin PB6 and use it for cooling fan tacho
Implemented X axis set and report mapping in M563 command and in web and
M408 status responses (but mapping doesn;t do anything yet)
Report number of axes to DWC
M307 H# A-1 C-1 D-1 disables the pid controller for that heater to free
up the pin
Debug print of matrixes during delta calibration is now to 4dp
Implemented fan blip
Support up to 6 axes in many commands
Allow creation of additional axes in M584
Display delta paremners to 3dp instead of 2dp
Removed M126/M127 error messages
Delta calibration now supports bed tilt parameters
On Duet WiFi, delta calibration is now done in double precision maths
Added support for G4 S parameter
Bed compensation or delta calibration is now aborted if the probe was
triggered at the start or was not triggered by the end of the probing
move
Bug fix: JSON file list returned by M20 S2 is now terminated by \n
Bug fix: stupidly high temperatures were returned immediately after
power up in response to status requests
Bug fix: when using an analog Z probe, probing movements were sometimes
aborted before the full depth had been probed but the firmware thought
that probing had terminated at the full depth
Bug fix: generic messages were sent to PanelDue in plain text format
Max temperature excursion and fault trigger time are now configurable
via M570
If a heater fault occurs then any SD card print in progress is abandoned
Improved M122 diagnostics headings
Bug fix: some values of pressure advance caused too many extruder steps
to be schedules, resulting in extruder step errors, and another bug in
the error handling then caused layer shifts
Changes to reduce incidence of false heating fault alarms, in particular
"temperature rising much more slowly than the expected 0.0C"
Stepper drivers beyond the first 5 are assumes to be non-TMC2660 drivers
Fixed doubling of M301 I parameter and halving of M301 P parameter
Implemented M303 auto tune and M307 heater process model
Improved temperature monitoring to detect heater cartridges or
thermistor falling out
Implemented M38 (thanks chrishamm)
Retructured course code tree
Add support for second SD card on SPI bus for Duet WiFi including
implementation of M21 and M22
New temperature monitoring
Increased PWM resolution
When uploading files to wifi module, skip empty blocks
Revised TMC driver in preparation for standstill current reduction
Fixed PrintMonitor bug when the slicer comment includes a '\' character
Further optimisation of step generation ISR
Don't allow more than half the capacity of the DDA queue to be frozen
Duet WiFi: print additional info from WiFi module
- Fix for uncommanded stepper motor movement on some systems following a
software reset
- When multiple motors are due to step, generate all the step pulses
simultaneously
- Added support for multiple drivers for a single axis (M584)
- Added support for extended step pulse width when using external
drivers (T parameter on M569 command)
- Removed XYZE params from M569 (use M584 instead)
- Added M913 command (set motor % of normal current)
- Added Z probe type 5, which is a normally-closed switch or active-high
probe connected to the Z probe connector
- Duet WiFi default Z probe threshold is now 500
- Duet WiFi defaults to using a low end homing switch on the X axis
Changes to use new pin modes in CoreNG
Initialise TMC2660 step/dir/CS pins as early as possible
Allow emergency stop in simulation mode
Disable drives and heaters when doing a software reset
Support 10th drive and 8th heater on Duet WiFi
TMC2660 driver support is now only in Duet WiFi firmware build
Fixed thermostatic fan bug introduced in version 1.13
Added MCU temperature monitoring
Duet WiFi only: added voltage monitoring, and disable TMC2660 drivers if
the voltage is too low or too high. Not tested as at time of this
checkin,
Temporary fix for RTD temperature spikes causing failed prints
Added 'only if printing a file' condition in M581 command
Fixed M117 for PanelDue
Don't print extruder positions in M114 because they are always zero
Process M0 and M1 when in simulation mode
Allow setting of fan PWM from 50% upwards when a fan is in thermostatic
mode
Reduced default extruder heater PWM frequency
Axes are no longer homes when microstepping is changed
SD card interface speed is included in M122 output
