Fixed bug with reading file info
Don't return status as Printing if just running a macro
Restored Json buffer back to 2000 bytes so as to return more files on SD
card
Limit the amount of moves we buffer so as to react faster to speed and
extrusion rate changes
Return print time left estimates in M105 S2 status response if printing
a file
Show stepper motor currents as integers and do some rounding to get more
accurate values
Added almost instant pause functonality
Support pause and resume macros
Support nested macros
Support zpl's web interface
Merge in zpl's web interface and network changes
Add R parameter to M105 command for PanelDue
M98 can now run macros from any SD card folder
Fixed G32 so that it really does run macro file bed.g if it exists
Added H parameter to M558 command
Added bed.g file for Mini Kossel with mechanical Z probe
Added M575 command to set baud rate and whether or not checksums are
required.
Default aux baud rate is now 57600.
Added support for a Z probe switch connected to the E0 endstop pins.
Added "geometry" variable in M105 S3 status response.
Fixes some possible issues in delta printing code
Don't apply Z probe XY correction when probing at current point with G30
with a P parameter
Added experimental simulation code, controlled by M37 for now
Added X and Y z-probe offsets to G31 command
Reworked G31 and G32 to do less work in the step ISR and to support Z
probe on delta printers
Z probe modulation pin is now selected using M558 R parameter instead of
probe type
Incorporated zpl's Network module updates and some of his Gcodes updated
Merged RRP's 0.96 Move code into mine
Added M105 S3, M20 S2 and M36 commands for supporting TFT control panel
Added X parameter to M305 command to allow thermistor channels to be
changed
Removed space after "B:" in M105 response to avoid confusing Pronterface
M0 no longer turns motors off
Updated M18 and M84 as per zpl fork
Don't insist that user provides values for all 5 possible extruders in
M906 command
Added Ormerod 2 sys files
Updated web interface files
Bug fix: M92 command would only set extruder steps/mm if either 1 or 5
extruder steps/mm was provided
Bug fix: Z-homing or bed probing when axis compensation was enabled
caused the X and Y origins to shift
We now mark drives as not homed when we disable them
File info code now supports gcode files generated by Simplify3D
Updated SD card files to latest web interface
Added more comments to config.g
Head movement commands that were in the tfree files have been moved to
the tpre files, to work better when G10 nozzle offsets are used
Increased default heater S factor to 1.0 to make it easier for users to
switch from RRP official firmware
Minor fix to move lookahead code
Added support for M570 command (set max time to hot)
M81 command now waits for moves to finish before turning power off
Other minor changes
Added modified lwip files that were missed from last checkin
Fixed incorrect JSON format in response to the rr_files command when no
files were found
Enabled hardware debounce filter on cooling fan RPM pin to get a correct
and stable readout
Fixed bug that caused the cooling fan PWM frequency to be 165kHz. It is
now 25kHz.
Fan RPM is now included in the web interface status response (thanks
zpl).
Many more error messages are now reported to the web interface as well
as the USB interface.
Interrupt-driven network timer task to better cope with slow SD card
writes (thanks zpl)
Module SamNonDuePin is now used for all digital and PWM pin I/O.
Fixed combined xyz move bug (thanks zpl). Reversed default direction of
X motor. Added support for M569 command. Fixed bug in execution of M503
command via web interface.
Refactored printing to strings and web server json response handling in
preparation for adding support for LCD display via serial link
Added a timer to record how long block writes to SD card take
Changed compiler optimization option to -O2 (was accidentally reset to
-Os in previous release)
Set the number of decimal places reported in the responses to various M
commands
Integrated zpl's changes to returning lists of files, returning info for
file being printed, and some network layer changes
Fixed bug: if 5 point bed compansation was used then doing G32 more than
once would try to move the head off the edge of the bed unless the first
4 probe coordinates were reset between them.
Fixed bug: if the last command in a a macro file did not end in newline
then it might not be fully executed
Bug fix: potential array underrun in Gcodes::Pop()
Reduced Z dive height back to 5mm
M563 command extended to allow the tool number origin to be adjusted. If
there is no P parameter in the command then the S parameter specifies an
offset to be added to tool numbers in T, G10, M104 and M109 commands.
This is so that multi-media gcode files generated by slic3r can be
printed without having to edit all the tool numbers in the gcode file
first. This extension is intended to be temporary, until slicer provides
a mechanism for specifying the tool numbers. A separate offset is
maintained for each data source (USB, web or SD card) and the offset for
data from the SD card is reset to zero when a new file is started. To
use this facility to print slic3r multi-media gcode files, add M563 S1
to your start gcode.
M104 and M109 commands now accept an optional T parameter to specify the
tool number, as generated by slic3r in multi-media gcode files.
Movement code from RepRapPro's dev branch incorporated, including
5-point manual or automatic bed compensation mechanism.
Heater status (off/standby/on) is included in the status poll response
for the web interface. This will be used in a future version of the web
interface.
Incorporated code from RepRapPro dev branch to allow many more
M-commands to return values as well as set them.
Incorporated code from RepRapPro dev branch to implement the M119 and
M135 commands. There is currently a bug in the M135 (set heat sample
interval) command, which means that if you change the interval from its
default value of 0.5 seconds then you need to adjust the I parameter by
the same ratio and the D parameter by the inverse ratio.
Extrusion totals are reset to zero when starting a new print from SD
card.
Fixed M122 so that diagnostics are sent to the web interface as well as
USB
Fixed M220 command to respond to speed change requests faster
Count the number of active extruders and heaters, and only send their
values to the web interface, subject to a minimum of 2 heaters and 1
extruder
Fixed buffer overrun bug in FTP LIST command that caused a subsequent
FTP delete command to crash. Increased file list buffer to 2000 bytes.
Added binary RepRapFirmware-057k-dc42.bin.
Corrected returned values of speed factor and extrusion factor
When setting the machine name and password, stop at the first control
character, and remove trailing spaces
Improved speed of response to M220 command
Limit length of text returned in response to rr_name web command, stop
on first control character, and escape and quote or backslash characters
Changed webserver to support HTTP requests that span multiple TCP
messages. Changed upload code to to block file writes direct fro the
received message. Increased maximum upload message size. Changed
fileinfo command to report layer height and what program generated the
gcode file, if available.
1. Reworked network layer to be more robust in the presence of network
errors (hopefully). In particular, don't release transmit buffers if
they might still be needed to retry sending data because the ACK got
lost.
2. Fixed bug whereby fileinfo command looked for the print height and
filament used if the extensio was .gcode or .gc or .gco but not if it
was .g.
3. When the M25 (pause print) command is received, pause the current
gcode so that commands such as M116 (wait for temperatures) can be
interrupted.
Rewrote the web server command parsing as a state machine. Added support
for persistent connections, used for file uploading. Changed file upload
protocol to pass status information back. Added web message type for
deleting files.
