Added new variable "extr" in Json response to report extruder positions
Added new fileinfo request type, returns file size, object height, and
total filament needed (if available)
Fixed bug in returning last command response in Json response
Disable interrupts when adding/removing network request structs from
linked lists, in case lwip does callbacks from ISR contexts
Firmware now recovers from USB disconnection without halting. Needs
changes to Arduino core library.
Added a timeout in the Spin() functions, which causes diagnostic info to
be stored and the system to be reset if a Spin() function takes more
than 20 seconds.
Completed changes to support multiple concurrent HTTP file requests.
Added support for new poll response for future support of additional
heaters and multiple extruders. Fixed a bug in reporting extruder
distance.
Changed webserver and network code to support multiple concurrent
connections
Removed support for differential-mode ultrasonic z-sensor
Reduced X and Y instantDv from 15 to 10 mm/sec to allow outlines of
holes to e drawn at lower speed
Changed temperature reading code to give thermistor disconnected reading
of -273C when there is a negative high ADC offset correction
Fixed bug introduced at version 057o-dc42 that broke the G32 bed
compensation. Added the Z heights of the bed compensation points to the
information displayed by M111 S2. Simplified the code that does
Z-probing in fast and slow stages. Added function sncatf and used it to
simplify the code in several places.
Tidied up axis homing tracking.
When checking endstops, wait for move to complete before accepting
further moves, otherwise subsequent moves use the wrong coordinates.
Temperatures and Z probes are now monitored continuously using a tick
interrupt to kick off ADC conversions. ADC is now run in 12-bit mode.
Thermistor readings are passed through averaging filters. Thermistors
are monitored for overheat conditions and bad readings in the tick ISR
and the appropriate heater is turned off (useful because the main loop
sometimes gets suspended while trying to do USB communication).
Use watchdog timer to monitor the tick interrupt - needs patch to
Arduino Due core library. Add facility to test watchdog timer (M111
S1001). Added an error status word to record that errors have occurred
(e.g. over-temperature).
M111 command changes so that S0 turns debug off, S1 turns debug on, S2
reports free memory - also now reports the type of the last restart and
the error status word. Fixed problem whereby M111 debug reports were not
sent to the web interface.
Implemented M999 command, which resets the Duet.
Removed an unused variable.
Changed some more "char*" to "const char*".
Changed extruder PID parameters and added more explanation for them.
1. Z-probing is now done in two stages: a fast stage at the configured
home feed rate until within 10% of the target value, then a slow stage
at 20% of that feed rate.
2. Provisional support for ultrasonic Z-probe.
3. Added calibration temperature and height temperature coefficient to Z
probe parameters.
4. Z-probe parameters and Z-probe type are now saved to flash memory so
that they survive power-off and reset cycles. Separate parameters are
retained for IR and ultrasonic probes in case both are fitted.
5. Fixed issue with doing slow Z-moves immediately after Z-homing or
probing.
Increase TCP window size from 1 to 2 packets and increase maximum amount
of web data sent to 1460. This decreases the page load time fro a
Windows client fro 6 seconds to less than 1 second. It also fixes a
problem whereby when using a Ubuntu client, file upload and direct print
didn't work unless the reprap.js file was edited to reduce the maximum
amount of data sent per request. Also we now initialize unused memory
with known data so that in response to the M111 S1 command we can better
estimate the amount of free memory.
Increase incoming web gcode buffer size to 1200 chars to allow more
gcodes to be sent in each message
Include free buffer size in poll response
Include response sequence number in poll response
Implement M30 (delete file) via USB interface
Support M503 and M111 commands via web interface
Added new fields "zprobe" and "resp" to webserver poll response
Immutable string parameters are passed as const char* not char*
Increase max number of files displayed to 42
Range-check heater parameters in incoming commands to avoid buffer
overflow if heater number is out of range
Improved network error recovery so that it it possible to reconnect
after some types of network error have occurred
Corrected calculation of temperatures to give more accurate results
towards the limits of the ADC range
