Implemented F, H and R parameters to M106 command. The second fan output
on a Duet 0.8.5 now defaults to being a thermostatic fan at power up.
Improved speed of file upload to SD card
G32 is now allowed if the printer has not been homed, if there is a
bed.g file
G30 commands are no longer allowed on a delta that has not been homed
M572 parameter P (drive number) replaced by parameter D (extruder
number)
File info requests are now processed in stages to reduce impact on
printing (thanks chrishamm)
Use latest network stack and webserver modules from chrishamm (thanks
chrishamm)
Added Roland mill support (thanks RRP/chrishamm)
Added S parameter (idle timeout) to M18 ans M84 commands (thanks
chrishamm)
Moved I/O pin assignments to separate Pins.h file to more easily support
alternative hardware (thanks dnewman)
Bug fix: filament usage and % print complete figures were incorrect when
absolute extruder coordinates were used
Bug fix: file-based print estimate was occasionally returned as 'inf'
which caused the web interface to disconnect
Bug fix: M666 now flags all towers as not homed
Bug fixes to extruder pressure compensation (M572 command).
New features
============
The PWM frequency for the heated bed and for any heater used as a
chamber heater is now 10Hz for bettercompatibility with DC-AC SSRs.
The PWM frequency for fans is now configurable using the F paramete ron
the M106 command. The default is 500Hz, which gives esonable control of
fans not designed for PWM. Increase it to 25000Hz when using 4-wire PWM
fans.
When a Duet 0.8.5 board is configured or detected, the fan control is
now automatically inverted. If you previously used M106 P0 I1 in
config.g to invert it, you will need to remove that.
M579 (scale Cartesian axes) is now implemented (thanks chrishamm).
M114, M119 and M573 commands can now be executed concurrently with other
commands.
When DDA debugging is enabled, the debug output now includes all active
extruders instead of just the first two.
M408 S0 now includes the fan speeds (for PanelDue).
M119 now reports the Z probe as well as the endstop switch states.
A tool can now be defined even if a tool with the same tool number
exists already. The existing tool will be shut down and deleted.
The bed heater can now be disabled using M140 S-1 (thanks chrishamm).
The chamber heater (if present) and the endstop switch states are now
reported to the web interface (thanks chrishamm).
Increased defauklt Z prove dive height to 5mm.
Increased default PID Ki to 0.2
Bug fixes
=========
On a CoreXY machine, XY speeds were too low by a factor of sqrt(2).
On a delta machine, after running auto calibration the Z=0 height could
be slightly inaccurate, depending on the difference between the X and Z
endstop corrections
When using a non-intelligent modulated Z probe on a Duet 0.8.5, the
modulation pin number was incorrect.
The M27 (Report SD card print status) response was inverted compared to
what it should be. When in Marlin mode it now includes the "byte n/m"
field that some versions of Pronterface expect.
Cold extrusion prevention did not work - an error message was generated,
but the extruder was driven anyway.
M999 PERASE is now more reliable (thanks chrishamm).
M23, M30 and M32 commands did not work when the filename parameter
passed included an absolute path.
//A T command inside a macro file did not execute the tool change macros
files.
A memory leak occurred when a tool was deleted.
All moves are now completed before switching to CoreXY mode.
Polling requests from PanelDue were not relied to when a macro was being
executed
M667 with no parameters returned an incorrect string
Added support for Duet 0.8.5 with auto detection between 0.6 and 0.85
board types
Added P parameter to M115 command to set board type
Changed M115 output to report the board type that was configured or
auto-detected
Improved ISR and step pulse generation efficiency to allow higher
movement speeds, especially wheh using 0.9deg/step motors
Added XYZE parameters to M569 command to allow driver remapping
Added R parameter to M569 command to allow enable signal to be reversed
when using external drivers (thanks dnewman)
Removed M558 R parameter because boare type 0.7 can now be set via M115
instead
Moved Fan0 RPM sense pin to PA14 to avoid conflict with Duet 0.8.5 FAN1
pin
M408 poll command can now be handled concurrently with other commands
Fixed CoreXY homing bug
Support simultaneous XY homing on CoreXY printers
Updated sample homeall.g file for CoreXY printers to do simultaneous XY
homing
Added H (height correction) parameter to G30 command
G30 S-1 now reports trigger height without changing ZS origin
Added M665 Z parameter to better support square delta printers
Changed interrupt priorities to make step pulse timing interrupt higher
priority than Ethernet (thanks zpl)
Fixed two potential divide by zero errors in PrintMonitor
Don't report an error if tpre, tpost or tfree macro file is not found
Changed the way we report bed height errors after bed probing without
calibration
Final Z probing speed is now always 1/3 of the initial probing speed as
set by M210
Bug fix: after Z probing the Z height was set incorrectly by 1 motor
microstep
Z axis min and max limits are now enforced if the axes have been homed
M665 command now shows the re-calculated delta radius and tower offsets
after auto-calibration
Initial and final RMS errors are now shown after delta auto-calibration
Pause/resume now mostly works when absolute extruder coordinates are
used
Doubled the maximum length of the SD card file listing that can be sent
to PanelDue
Implemented zpl's Network and PrintMonitor changes including M404
(thanks, zpl)
Increased default maximum instantaneous speed changes
Bug fix:: if M226 was used to pause the print, the resume coordinates
were not set up correctly
Bug fix: when changing the travel direction, the head was sometimes
slowed down more than necessary
Bug fix: warm-up time was not shown correctly in DuetWebControl
Bug fix: extruder drive positions were always shown as 0.0 in
DuetWebControl
Bug fix: incorrect PID parameters were shown in response to M301
Replaced old web interface files on SD card by DuetWebControl
Modified all resume.g files to set the speed when moving to the paused
head coordinates
Merged in zpl's latest changes to Network and Print Monitor modules,
providing DHCP and Netbios name support
Added command M999 S4321 to unlock flash memory, reset and boot to BOSSA
port
Z dive height is now relative to Z probe trigger height and default is
reduced to 3mm
Added experimental support for acoustic probe for delta printers
Bug fix: firmware once again prevents Z homing before X and Y are homed,
if the Z probe is used for Z homing
Various code tidying
Implemented rr_config web request for zpl's latest web interface
Implemented 7-factor auto calibration for delta printers
Fix bug with fileinfo calls corrupting memory
M563 can now be used to delete tools
Prevent setting of absurdly high hot end temperatures
Added R parameter to G1 to go back to previous location, with optional
offsets
Allow Pronterface and PanelDue M105 requests to execute during file
macros etc.
Added more status information for PanelDue to M105 S2 command
Send replies when prints are paused, resumed or cancelled
Added missing newlines at end of M105 responses
Increased X and Y course homing speeds
Fixed bug with reading file info
Don't return status as Printing if just running a macro
Restored Json buffer back to 2000 bytes so as to return more files on SD
card
Limit the amount of moves we buffer so as to react faster to speed and
extrusion rate changes
Return print time left estimates in M105 S2 status response if printing
a file
Show stepper motor currents as integers and do some rounding to get more
accurate values
Added almost instant pause functonality
Support pause and resume macros
Support nested macros
Support zpl's web interface
Merge in zpl's web interface and network changes
Add R parameter to M105 command for PanelDue
M98 can now run macros from any SD card folder
Fixed G32 so that it really does run macro file bed.g if it exists
Added H parameter to M558 command
Added bed.g file for Mini Kossel with mechanical Z probe
Added M575 command to set baud rate and whether or not checksums are
required.
Default aux baud rate is now 57600.
Added support for a Z probe switch connected to the E0 endstop pins.
Added "geometry" variable in M105 S3 status response.
Fixes some possible issues in delta printing code
Don't apply Z probe XY correction when probing at current point with G30
with a P parameter
Added experimental simulation code, controlled by M37 for now
Added X and Y z-probe offsets to G31 command
Reworked G31 and G32 to do less work in the step ISR and to support Z
probe on delta printers
Z probe modulation pin is now selected using M558 R parameter instead of
probe type
Incorporated zpl's Network module updates and some of his Gcodes updated
Merged RRP's 0.96 Move code into mine
Added M105 S3, M20 S2 and M36 commands for supporting TFT control panel
Added X parameter to M305 command to allow thermistor channels to be
changed
Removed space after "B:" in M105 response to avoid confusing Pronterface
Added support for nozzle offsets in G10 command
Disable heater timeout if the time limit is set to zero or negative
Don't send non-error responses to the web interface unless the
corresponding command also came from the web interface
Added support for aux input from serial. Need to finish this by making
serial transmission interrupt-driven.
Refactored printing to strings and web server json response handling in
preparation for adding support for LCD display via serial link
Added a timer to record how long block writes to SD card take
M563 command extended to allow the tool number origin to be adjusted. If
there is no P parameter in the command then the S parameter specifies an
offset to be added to tool numbers in T, G10, M104 and M109 commands.
This is so that multi-media gcode files generated by slic3r can be
printed without having to edit all the tool numbers in the gcode file
first. This extension is intended to be temporary, until slicer provides
a mechanism for specifying the tool numbers. A separate offset is
maintained for each data source (USB, web or SD card) and the offset for
data from the SD card is reset to zero when a new file is started. To
use this facility to print slic3r multi-media gcode files, add M563 S1
to your start gcode.
M104 and M109 commands now accept an optional T parameter to specify the
tool number, as generated by slic3r in multi-media gcode files.
Movement code from RepRapPro's dev branch incorporated, including
5-point manual or automatic bed compensation mechanism.
Heater status (off/standby/on) is included in the status poll response
for the web interface. This will be used in a future version of the web
interface.
Incorporated code from RepRapPro dev branch to allow many more
M-commands to return values as well as set them.
Incorporated code from RepRapPro dev branch to implement the M119 and
M135 commands. There is currently a bug in the M135 (set heat sample
interval) command, which means that if you change the interval from its
default value of 0.5 seconds then you need to adjust the I parameter by
the same ratio and the D parameter by the inverse ratio.
Extrusion totals are reset to zero when starting a new print from SD
card.
M301 and M304 commands to set PID parameters now take an additional S
parameter. This allows for variations in cartridge heater power and
supply voltage to be taken into account more easily.
Temperature errors are reported to the web server as well as to USB.
The Heat section of the M122 diagnostics report now shows the
accumulated PID I-term.
G90 and G91 commands now affect only the the axes, not the extruders.
Bug fix: numerous calls to strncat were being made with a 'nchars'
parameter that was larger than space available in the destination
buffer.
Bug fix: print moves received just prior to an M109 or M190 command were
not executed until after the heater had reached temperature instead of
before.
Bug fix: using G10 to set oly the active temperature caused the standby
temperature to be set to an undefined value, and vice versa
G10 can now be used to retrieve the active and standby temperatures as
well as set them
Bug fix: I and D parameters were set to incorrect values when the M301
and M304 commands were used. They also reported the incorrect values.
New T parameter added to M301 and M304 commands, to allow the I term to
be preset to a suitable value when PID kicks in
Adjusted default PID parameters for lower overshoot and less oscillation
Bug fix: when axis or bed compensation was enabled a homing move to seek
for one endstop could be prematurely terminated by another endstop
M122 command only outputs LWIP stats if debug is enabled. Prevents a
hang if no UDB cable is connected when M122 is executed.
Bug fix: when resetting, the heaters used to power up for a short time
M0 and M1 commands now turn the heaters off instead of to standby
Web server status poll response now includes the selected tool number
Fixed M122 so that diagnostics are sent to the web interface as well as
USB
Fixed M220 command to respond to speed change requests faster
Count the number of active extruders and heaters, and only send their
values to the web interface, subject to a minimum of 2 heaters and 1
extruder
Corrected returned values of speed factor and extrusion factor
When setting the machine name and password, stop at the first control
character, and remove trailing spaces
Improved speed of response to M220 command
Limit length of text returned in response to rr_name web command, stop
on first control character, and escape and quote or backslash characters
1. Reworked network layer to be more robust in the presence of network
errors (hopefully). In particular, don't release transmit buffers if
they might still be needed to retry sending data because the ACK got
lost.
2. Fixed bug whereby fileinfo command looked for the print height and
filament used if the extensio was .gcode or .gc or .gco but not if it
was .g.
3. When the M25 (pause print) command is received, pause the current
gcode so that commands such as M116 (wait for temperatures) can be
interrupted.
Introduced new file upload protocol that doesn't use gcodes and allows
upload errors to be reported back. Changed file system interface in
Platform to return success/fail status of Write and Close calls to
support this.
Added new request code rr_data for file uploading, and made other
changes to improve file upload speed.
Implemented S parameter to M208 command, to allow the negative limits of
axes to be set. Also reports current limits of no X/Y/Z parameter.
Reduced max reported free buffer size to 950 bytes to avoid problems
with file upload from Windows 8.1.
Fixed bug whereby incoming gcodes were URI-decoded twice, which could
cause problems if a comment contain a % character
Fixed bug whereby M109 and M190 waited for all heaters to reach target
temperature instead of just the one involved
Fixed bug whereby files whose names contain an uppercase letter G could
not be uploaded or deleted
Increase buffer size for incoming gcodes
Removed parameter to set max PWM value in M106 command. Max PWM value is
now 255 as per recent RepRapPro change.
Changed the code that deals with dropping characters in unimportant
messages sent to USB such that we only drop characters at the end of a
line (adding ".\n" to whatever we send) or drop whole lines
Fixed problem whereby gcode files printed from SD card that used lots of
small fast moves in sequence would print jerkily if a network cable had
not been connected since reset.
Fixed problem whereby object height and filament needed were not
retrieved from the SD card file to be printed if the filename contained
spaces.
Added support for deprecated M190 command, because slic3r appears to
generate it sometimes
Added support for M564 command to allow movement without limits, copied
from RepRapPro dev branch
If a network error occurs when sending a file, we now close that file,
otherwise we would use up open file entries. Also added number of
available open file entries to M111 S2 command.
Fixed bug in file handling that affected SD card pause/resume
operations. Merged changes from zombiepantslol to allow a height to be
set for a Z endstop switch. Reverted to blocking USB I/O but only for
debug and M503 output. Added return codes for file close and seek
operations. Increased the size of the tail of the file that we scan for
G1 Z commands from 32K to nearly 200K.
Fixed a bug when one file was called from another
M111 S2 command now displays time since last reset
M106 'I' parameter now only inverts fan PWM when >0
Non-homing moves when bed probing are now done at max speed
M999 reset command now delays 0.5 second to allow response to be sent
back to browser, otherwise it may retry the reset
Reduced block read size when retrieving file info to work around an
intermittent bug that causes the SDHC card/ FATfs stack to return data
from the wrong sector sometimes. Tidied up some other code.
Added new variable "extr" in Json response to report extruder positions
Added new fileinfo request type, returns file size, object height, and
total filament needed (if available)
Fixed bug in returning last command response in Json response
Disable interrupts when adding/removing network request structs from
linked lists, in case lwip does callbacks from ISR contexts
Changed network startup to avoid long delay if no network cable is
connected
Enable DHCP support if IP address is configured as 0.0.0.0 (not working
yet)
Move thermistor parameters to M305, added parameter to configure series
resistance
Added B and W PID parameters
Firmware now recovers from USB disconnection without halting. Needs
changes to Arduino core library.
Added a timeout in the Spin() functions, which causes diagnostic info to
be stored and the system to be reset if a Spin() function takes more
than 20 seconds.
